Secunia CSI7
Advisories
Research
Forums
Create Profile
Our Commitment
PSI
PSI API
CSI
OSI
xSI
Vulnerabilities
Programs
Open Discussions
My Threads
Create Thread
Statistics
About

Forum Thread: PSI.lnk disabled

You are currently viewing a forum thread in the Secunia Community Forum. Please note that opinions expressed here are not of Secunia but solely reflect those of the user who wrote it.

This thread was submitted in the following forum:
PSI

This thread has been marked as locked.
Croysdale PSI.lnk disabled
Member 10th Jan, 2010 22:50
Ranking: 0
Posts: 6
User Since: 10th Jan, 2010
System Score: N/A
Location: N/A
Last edited on 10th Jan, 2010 22:57

When I turn on my computer (or re-boot) I get the message 'Secunia PSI.lnk disabled'. Can anyone tell me what this means please?

Anthony Wells RE: PSI.lnk disabled
Expert Contributor 11th Jan, 2010 22:56
Score: 2414
Posts: 3,310
User Since: 19th Dec 2007
System Score: N/A
Location: N/A
Last edited on 11th Jan, 2010 23:01
It means that PSI is not enabled to run in your computer's "StartUp Menu" .

You should be able to enable it using your PSI's "settings" tab , tick the box to "Start the Secunia PSI on Boot" , if that is your wish.

You need to be in to "advanced" mode (selection is at the top right of any PSI page) to see the "settings" tab .

As this is your first post , I will give you some basic advice (sorry if you already know) , which may help you explain any problems to us more specifically :-


To help resolve any problem , here are some instructions to help you first of all get the best out of PSI :-

1)use PSI in "advanced" mode ;
2)in the "settings" tab make sure that the box in the first/upper section is NOT ticked in order to have the maximum info available ;
3)tell us in which "tab(s)" your problem programme is located ;
4)in that tab , click on the + in the box at the left end of the programme , the page will expand ;
5)in the expanded page , tell us what is written in the "installation path" ;
6)in the "toolbox" section , lower down , the link "technical details" should confirm the installation path details ;
7)click on the link "open folder" and you will see more details concerning the location of the "problem" .

Posting these details will help the Forum help you , if/when you have a problem .

Take care
Anthony

--


It always seems impossible until its done.
Nelson Mandela
Was this reply relevant?
+0
-0
Croysdale RE: PSI.lnk disabled
Member 12th Jan, 2010 12:28
Score: 0
Posts: 6
User Since: 10th Jan 2010
System Score: N/A
Location: N/A
Thank you Anthony for your reply. I now understand the workings of PSI much better. Thank you also for the instructions on reporting any further problems.
Best wishes
Rex Sara
Was this reply relevant?
+0
-0

This thread has been marked as locked.


 Products Solutions Customers Partner Resources Company
 
 Corporate
Vulnerability Intelligence Manager (VIM)
Corporate Software Inspector (CSI)
Consumer
Personal Software Inspector (PSI)
Online Software Inspector (OSI)
 Industry
Compliance
Technology
Integration
 Customers
Testimonials
 VARS
MSSP
Technology Partners
References
 Reports
Webinars
Events
 About us
Careers
Memberships
Newsroom


 
© 2002-2014 Secunia ApS - Rued Langgaards Vej 8, 4th floor, DK-2300 Copenhagen, Denmark - +45 7020 5144
Terms & Conditions and Copyright - Privacy - Report Vulnerability